# Creality CR M4 **URL:** https://3dprintingspace.com/c/filament-3d-printer/creality-cr-m4/131.md [Latest](https://3dprintingspace.com/latest.md) · [Categories](https://3dprintingspace.com/categories.md) --- ## [About the Creality CR M4 category](https://3dprintingspace.com/t/about-the-creality-cr-m4-category/6557)
**Author:** [@Jason](https://3dprintingspace.com/u/Jason)\ **Replies:** 0\ **Last updated:** [June 7, 2023, 2:05pm UTC](https://3dprintingspace.com/t/about-the-creality-cr-m4-category/6557 "2023-06-07T14:05:00Z")
This Category is dedicated to any issues or problems dedicated to the CR M4 3D printer. Post up any Hints, Links or tricks you have learned using this printer. If you have a problem, Post it as well and let the communi… --- ## [CR-M4 Cura Profile](https://3dprintingspace.com/t/cr-m4-cura-profile/6574)
**Author:** [@Jason](https://3dprintingspace.com/u/Jason)\ **Replies:** 8\ **Last updated:** [January 31, 2025, 2:53am UTC](https://3dprintingspace.com/t/cr-m4-cura-profile/6574 "2025-01-31T02:53:45Z")
For the Printer setup, I used a CR-10 Max and updated the retractions from 6.5 to .5mm The printing profile is located here --- ## [Warping/ Lifting - Initial layer peels up](https://3dprintingspace.com/t/warping-lifting-initial-layer-peels-up/9615)
**Author:** [@balks](https://3dprintingspace.com/u/balks)\ **Replies:** 3\ **Last updated:** [November 22, 2024, 9:48pm UTC](https://3dprintingspace.com/t/warping-lifting-initial-layer-peels-up/9615 "2024-11-22T21:48:27Z")
CR-M4 Creality Printer 3D Printing Canada - White Budget PLA Filament: 1.75mm Initial print layer peels up off of the bed almost immediately. Tends to warp back towards the previous outer layer. I’ve tried slowing the … --- ## [Z offset set to -50 still not printing](https://3dprintingspace.com/t/z-offset-set-to-50-still-not-printing/8640)
**Author:** [@NickGarai](https://3dprintingspace.com/u/NickGarai)\ **Replies:** 1\ **Last updated:** [June 8, 2024, 4:21pm UTC](https://3dprintingspace.com/t/z-offset-set-to-50-still-not-printing/8640 "2024-06-08T16:21:41Z")
I have set my z offset to -50 and I am still unable to print. Do I have to adjust my speed? Temperature? What am I doing wrong? Am I missing something? --- ## [I have my cr m4 all dialed in with simplifty3d slicer](https://3dprintingspace.com/t/i-have-my-cr-m4-all-dialed-in-with-simplifty3d-slicer/7816)
**Author:** [@1954\_3d\_printer](https://3dprintingspace.com/u/1954_3d_printer)\ **Replies:** 0\ **Last updated:** [February 20, 2024, 7:51am UTC](https://3dprintingspace.com/t/i-have-my-cr-m4-all-dialed-in-with-simplifty3d-slicer/7816 "2024-02-20T07:51:57Z")
CR M4 is a good printer once all the bugs are cleaned out. I have great sucess with .6mm nozzles and .4 layer height. hit me up if you need a factory file. --- ## [Connecting to Pronterface...checking E-steps etc](https://3dprintingspace.com/t/connecting-to-pronterface-checking-e-steps-etc/7309)
**Author:** [@hawleyk](https://3dprintingspace.com/u/hawleyk)\ **Replies:** 1\ **Last updated:** [October 30, 2023, 2:57pm UTC](https://3dprintingspace.com/t/connecting-to-pronterface-checking-e-steps-etc/7309 "2023-10-30T14:57:10Z")
Has anyone here attempted to connect their M4 to a laptop for Pronterface to check e-steps? I was able to get it to connect but it does nothing when i send a command…so odd? anyone have any thoughts? --- ## [X axis will not auto-home](https://3dprintingspace.com/t/x-axis-will-not-auto-home/7301)
**Author:** [@hawleyk](https://3dprintingspace.com/u/hawleyk)\ **Replies:** 7\ **Last updated:** [October 29, 2023, 11:28pm UTC](https://3dprintingspace.com/t/x-axis-will-not-auto-home/7301 "2023-10-29T23:28:28Z")
Hi, I’ve had my M4 for a few months. It worked great at first but then I had an epic print failure overnight and the x-axis belt pulled off…Everything was messed up and it has taken me a few weeks to get it back to Almo…