# Ender 5 Pro Limit Switch **URL:** \ **Category:** 3D Printers\ **Created:** [May 12, 2021, 12:04pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508 "2021-05-12T12:04:24Z")\ **Posts on this page:** 8\ **Page:** 1
**Author:** ![GlennW](https://3dps-assets.b-cdn.net/letter_avatar_proxy/v4/letter/g/b782af/32.png) [@GlennW](https://3dprintingspace.com/u/GlennW)\ **Post date:** [May 12, 2021, 12:04pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/1 "2021-05-12T12:04:24Z")
Hello, My ender 5 Pro seems to need its limit switch adjusted for whatever reason. The Bed is crashing into the filament tip head. I can see the limit switch is not yet engaged and when I try to set an auto home to compensate it cannot adjust and goes negative. Any ideas how to adjust the Z axis. Edit: This issue is resolved I just had a blonde moment, and went in the wrong direction with the bed adjustments. ---
**Author:** ![Dr.Marvin](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/dr.marvin/32/195_2.png) [@Dr.Marvin](https://3dprintingspace.com/u/Dr.Marvin)\ **Post date:** [May 12, 2021, 12:07pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/2 "2021-05-12T12:07:15Z")
Can you share a picture of the limit switch thats not doing its job? ---
**Author:** ![Dr.Marvin](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/dr.marvin/32/195_2.png) [@Dr.Marvin](https://3dprintingspace.com/u/Dr.Marvin)\ **Post date:** [May 12, 2021, 12:14pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/3 "2021-05-12T12:14:32Z")
Can you do a manual level successfully? ---
**Author:** ![Jason](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/jason/32/6148_2.png) [@Jason](https://3dprintingspace.com/u/Jason)\ **Post date:** [May 12, 2021, 2:09pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/4 "2021-05-12T14:09:16Z")
Just a knee jerk reaction but how loose are your bed springs? If you tighten them down all the way does it still hit the nozzle? ---
**Author:** ![GlennW](https://3dps-assets.b-cdn.net/letter_avatar_proxy/v4/letter/g/b782af/32.png) [@GlennW](https://3dprintingspace.com/u/GlennW)\ **Post date:** [May 12, 2021, 2:22pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/5 "2021-05-12T14:22:00Z")
I am really embarrassed to admit this. So I added supports and my bed became unleveled, so I thought Ill loosen the screens and that will lower the bed. Ya when I tightened them it works. I am so sorry, that was so dumb of me. You are right hahahaha ---
**Author:** ![Dr.Marvin](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/dr.marvin/32/195_2.png) [@Dr.Marvin](https://3dprintingspace.com/u/Dr.Marvin)\ **Post date:** [May 12, 2021, 3:05pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/6 "2021-05-12T15:05:58Z")
All good πŸ™‚ weve all made mistakes like that before πŸ™‚ ---
**Author:** ![Jason](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/jason/32/6148_2.png) [@Jason](https://3dprintingspace.com/u/Jason)\ **Post date:** [May 13, 2021, 1:35pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/7 "2021-05-13T13:35:34Z")
Hey, @GlennW don’t ever be embarrassed. I’ve been at this close for 15 years and the reason I mentioned it cause it happened to me. (and not just once) πŸ™‚ ---
**Author:** ![PJprincefpv](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/pjprincefpv/32/262_2.png) [@PJprincefpv](https://3dprintingspace.com/u/PJprincefpv)\ **Post date:** [May 13, 2021, 7:33pm UTC](https://3dprintingspace.com/t/ender-5-pro-limit-switch/2508/8 "2021-05-13T19:33:44Z")
There is also a little adjustment screw on the back of the bed so you can adjust the height as well as using the bedspring knobs to adjust