# Noir and Monocure

**URL:** <https://3dprintingspace.com/t/noir-and-monocure/1194>\
**Category:** Peopoly Noir\
**Created:** [February 5, 2021, 8:29pm UTC](https://3dprintingspace.com/t/noir-and-monocure/1194 "2021-02-05T20:29:40Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![BullfrogPro](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/bullfrogpro/32/514_2.png) [@BullfrogPro](https://3dprintingspace.com/u/BullfrogPro)\
**Post date:** [February 5, 2021, 8:29pm UTC](https://3dprintingspace.com/t/noir-and-monocure/1194/1 "2021-02-05T20:29:40Z")

</div>

Just curious if anyone else is using Monocure Rapid resin on their Noir?

---

<div class="post-metadata">

**Author:** ![Jason](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/jason/32/6148_2.png) [@Jason](https://3dprintingspace.com/u/Jason)\
**Post date:** [February 5, 2021, 8:40pm UTC](https://3dprintingspace.com/t/noir-and-monocure/1194/2 "2021-02-05T20:40:14Z")

</div>

Hey Bullfrog

Welcome to the forum

Jason H

---

<div class="post-metadata">

**Author:** ![Keith](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/keith/32/92_2.png) [@Keith](https://3dprintingspace.com/u/Keith)\
**Post date:** [February 5, 2021, 8:52pm UTC](https://3dprintingspace.com/t/noir-and-monocure/1194/3 "2021-02-05T20:52:31Z")

</div>

Hello BullfrogPro

Yes, we have been trying it here at the Store. Mostly the Grey and Clear.  
we’ve been using the settings from Monocure.  
[https://monocure3d.com.au/printer-settings](https://monocure3d.com.au/printer-settings)

---

<div class="post-metadata">

**Author:** ![BullfrogPro](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/bullfrogpro/32/514_2.png) [@BullfrogPro](https://3dprintingspace.com/u/BullfrogPro)\
**Post date:** [February 21, 2021, 5:38am UTC](https://3dprintingspace.com/t/noir-and-monocure/1194/4 "2021-02-21T05:38:55Z")

</div>

Hi Jason Hi Keith

I was the one who sent you guys the settings from Monocure lol

Was just curious who else was using it and if they were seeing any issues.  
I have been using times down to 1s per layer which works fine and the only issue is the size/weight of the prints causing plate adhesion. Just trying to see if bring up the resin vat temp to about 26°C will cure that. Other than that issue both printer and resin doing well.

Dave

---

<div class="post-metadata">

**Author:** ![Keith](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/keith/32/92_2.png) [@Keith](https://3dprintingspace.com/u/Keith)\
**Post date:** [February 22, 2021, 12:18am UTC](https://3dprintingspace.com/t/noir-and-monocure/1194/5 "2021-02-22T00:18:36Z")

</div>

@BullfrogPro

Dave,  
Yes we’ve had a few Customers that have seen very different Prints qualities, affected by fluctuating Garage Temps, this winter!