# Some problems after install sprite pro and crtouch on 3v2 **URL:** \ **Category:** Creality Ender 3 / 3 Pro / V2\ **Created:** [July 4, 2023, 12:34pm UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680 "2023-07-04T12:34:41Z")\ **Posts on this page:** 7\ **Page:** 1
**Author:** ![zaphiel](https://3dps-assets.b-cdn.net/letter_avatar_proxy/v4/letter/z/85f322/32.png) [@zaphiel](https://3dprintingspace.com/u/zaphiel)\ **Post date:** [July 4, 2023, 12:34pm UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680/1 "2023-07-04T12:34:41Z")
Hello all. I have not seen any thread with similar problems or that solves my problems, if there is something, link it to me in case I have missed it. After installing sprite pro and crtouch, with the firmware Ender3V2-422-BLTUBL-T13-MPC-20230524, and the dacai for the screen, I can’t level the bed in any way (I changed the wheels) In addition to not leveling, I am touching the probe settings, now when doing bed tramming front/back left/right, the nozzle and crtouch stays inside the bed, but it seems that the virtual position of the bed has moved to the left, also , that if I start to print, it does so in the front left corner. I also have a cable labeled E left over in the same set of cables that goes to the X motor, I think it is left over but I’m not sure. Any ideas? Thank you. ---
**Author:** ![Loosenut](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/loosenut/32/3612_2.png) [@Loosenut](https://3dprintingspace.com/u/Loosenut)\ **Post date:** [July 4, 2023, 9:00pm UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680/2 "2023-07-04T21:00:58Z")
Did you unhook the Z axis stop, left side vertical frame member. ---
**Author:** ![zaphiel](https://3dps-assets.b-cdn.net/letter_avatar_proxy/v4/letter/z/85f322/32.png) [@zaphiel](https://3dprintingspace.com/u/zaphiel)\ **Post date:** [July 4, 2023, 9:39pm UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680/3 "2023-07-04T21:39:58Z")
Where? z axis move correctly aparently. Dont change z stop when i did the change extruder. ---
**Author:** ![Loosenut](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/loosenut/32/3612_2.png) [@Loosenut](https://3dprintingspace.com/u/Loosenut)\ **Post date:** [July 4, 2023, 9:54pm UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680/4 "2023-07-04T21:54:36Z")
When you install a CR Touch it becomes your Z stop. You are suppose to disable the original Z stop. It could be causing a conflict. Its at the bottom outside face on the left vertical frame. Just unplug it. ---
**Author:** ![zaphiel](https://3dps-assets.b-cdn.net/letter_avatar_proxy/v4/letter/z/85f322/32.png) [@zaphiel](https://3dprintingspace.com/u/zaphiel)\ **Post date:** [July 4, 2023, 10:20pm UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680/5 "2023-07-04T22:20:07Z")
I’ll try it. But that not cause the bed virtual displacement, right? And that it prints in the corner instead of the center, what can it be? ---
**Author:** ![Loosenut](https://3dps-assets.b-cdn.net/user_avatar/3dprintingspace.com/loosenut/32/3612_2.png) [@Loosenut](https://3dprintingspace.com/u/Loosenut)\ **Post date:** [July 4, 2023, 11:06pm UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680/6 "2023-07-04T23:06:41Z")
No it wouldn’t. I can’t remember what it is but there is a setting that can change the print origin. Maybe something in the new firmware needs to be set differently. If there is a cable left unhooked that that might cause problems too. If it is marked E then it should be for the extruder. ---
**Author:** ![zaphiel](https://3dps-assets.b-cdn.net/letter_avatar_proxy/v4/letter/z/85f322/32.png) [@zaphiel](https://3dprintingspace.com/u/zaphiel)\ **Post date:** [July 5, 2023, 7:52am UTC](https://3dprintingspace.com/t/some-problems-after-install-sprite-pro-and-crtouch-on-3v2/6680/7 "2023-07-05T07:52:23Z")
I disabled z axis stop, don´t see nothing changed. The E cable unhook i guess is from stock extruder. Don´t understand why doing bed tramming to home front/back left/right corners, It seems that it is moved. These are the back positions, seems moved to the right ![photo_2023-07-05_09-47-15](https://storage.3dprintingspace.com/original/2X/0/0202bba52ae8e525408b46264a2de369b5ec4b53.jpeg) ![photo_2023-07-05_09-47-21](https://storage.3dprintingspace.com/original/2X/d/df3e14e79b5f5827e35159580b2fd35242be0c91.jpeg) Also, I’m sticking with the probe settings, it’s the distance moved with respect to your home plate, is that right? Thanks a lot.