Filament 3D Printer Technical Help Creality Ender 5 / 5 Pro
Topic | Replies | Views | Activity | |
---|---|---|---|---|
Ender 5/5 Pro Specs
220x220x300mm build area (8.6 x 8.6 x 11.8 inches) Heated bed Magnetic sticker build platform Resume printing after power loss Filament Diameter - 1.75mm Heated Bed Power Supply AC input 115/230V, DC output 24V 270W Net… |
![]() |
2 | 114 | May 25, 2022 |
About the Creality Ender 5 / 5 Pro category
|
![]() |
0 | 214 | January 25, 2021 |
Ender 5 plus stock board Klipper fubar
|
![]() ![]() ![]() |
9 | 39 | January 26, 2023 |
Ender 5 Pro not responsive screen blank
|
![]() ![]() ![]() ![]() |
5 | 59 | January 19, 2023 |
Extruder cannot push filament through my all metal hot end
|
![]() ![]() ![]() ![]() ![]() |
17 | 542 | January 9, 2023 |
Print adhesion, too good?
|
![]() ![]() |
11 | 102 | December 13, 2022 |
Ender 5 Temp contol issue
|
![]() ![]() |
6 | 59 | December 6, 2022 |
Linear Rail kit setup
|
![]() ![]() ![]() |
2 | 515 | December 5, 2022 |
Standard Ender 5 Hemera Upgrade
|
![]() ![]() |
10 | 125 | October 21, 2022 |
CR Touch on an Ender5 pro
|
![]() ![]() ![]() ![]() ![]() |
38 | 2371 | September 8, 2022 |
Unwanted filament unload
|
![]() ![]() ![]() ![]() ![]() |
10 | 285 | July 26, 2022 |
BLtouch Problem Ender Pro
|
![]() ![]() ![]() |
13 | 232 | June 17, 2022 |
5+ Heating less on one side...?
|
![]() ![]() |
2 | 77 | June 13, 2022 |
Ender 5 Pro/bltouch -- z-offset not used
|
![]() ![]() |
5 | 517 | June 2, 2022 |
Hemera Upgrade (Following Tutorial -- Got Stuck)
|
![]() ![]() ![]() |
30 | 432 | May 31, 2022 |
BLTouch not probing bed
|
![]() ![]() ![]() |
8 | 186 | May 20, 2022 |
What would the cause of this be?
|
![]() ![]() ![]() ![]() |
6 | 192 | May 10, 2022 |
Ender 5 Pro CR Touch failed
|
![]() ![]() ![]() ![]() ![]() |
14 | 998 | April 7, 2022 |
Ender5 to 5Pro issue
|
![]() ![]() ![]() |
5 | 187 | April 6, 2022 |
Prusaslicer settings for bridging
|
![]() ![]() ![]() ![]() |
9 | 143 | February 28, 2022 |
Ender 5 Pro stuck on E Heating
|
![]() ![]() ![]() ![]() |
8 | 793 | February 3, 2022 |
Ender 5 Plus / Cura start up file and G29
|
![]() ![]() ![]() ![]() |
14 | 285 | January 31, 2022 |
Ender 5 Pro Strange Behavior ? (Jason?)
|
![]() ![]() ![]() ![]() |
7 | 278 | January 14, 2022 |
Ender 5plus help in St. Catharines
|
![]() ![]() ![]() |
11 | 237 | December 10, 2021 |
Abs printer settings
|
![]() ![]() |
1 | 311 | December 5, 2021 |
Petg settings recommended
|
![]() ![]() ![]() ![]() ![]() |
4 | 764 | October 31, 2021 |
First Petg print
|
![]() ![]() ![]() ![]() |
4 | 277 | October 30, 2021 |
Layer Height to high?
|
![]() ![]() ![]() ![]() |
4 | 276 | September 28, 2021 |
Why is this printing like this
|
![]() ![]() ![]() |
11 | 346 | September 7, 2021 |
Ribbon cable size
|
![]() ![]() |
1 | 347 | July 11, 2021 |